Registration Page

[ksamdj]

After the installation of EMC 9, every time I tried to open an application I would get the registration page that would promp me for my e-mail address, name and country. After doing this numerous times (closing and reopening program and reboot) I became frustrated and removed the program. I want to reinstall the program but I have been reading this forum and want to be shure that I can get it up and running without any more grief. I have already been bewildered over the crash of vers 7.

 

ALSO, I noticed that when I did install the EMC 9 "Complete" during the install I was never prompted for the Content Disc. Is this normal?

[ksamdj]

You have to uninstall both IE 7 and EMC 7, reboot, and install EMC 7 again. I had to do that with EMC 7.5.

 

The unfortunate thing is IE 7 ruined a multitude of programs. I didn't care for IE 7, so I am back at IE 6.

 

 

Alright. I have followed all of the advise I read from this forum and I now have EMC 9 back on my system:

 

Why do I receive the registration page asking for my e-mail, name and country every time I open an application??? And, when I log in here to this website it shows that I have TWO Roxio Suite 9 regitered. What the heck is going on?

[grandpabruce]

Alright. I have followed all of the advise I read from this forum and I now have EMC 9 back on my system:

 

Why do I receive the registration page asking for my e-mail, name and country every time I open an application??? And, when I log in here to this website it shows that I have TWO Roxio Suite 9 regitered. What the heck is going on?

 

Yikes! Contact Roxio directly. Maybe someone from Roxio will drop by here, and help.

[ksamdj]

Try uninstalling and re-installing

 

This forum for a blow-by-blow 'howto'

 

http://forums.support.roxio.com/index.php?...amp;#entry79483

 

I have already un-installed / re-installed. NOW my computer will not boot from the off position. I have to go to safe mode and then re-start. What the *&$ is going on. I am getting really fed up with this program. I am spending too much time trying to make it work.

[gi7omy]

Try uninstalling and re-installing

 

This forum for a blow-by-blow 'howto'

 

http://forums.support.roxio.com/index.php?...amp;#entry79483

[grandpabruce]

After the installation of EMC 9, every time I tried to open an application I would get the registration page that would promp me for my e-mail address, name and country. After doing this numerous times (closing and reopening program and reboot) I became frustrated and removed the program. I want to reinstall the program but I have been reading this forum and want to be shure that I can get it up and running without any more grief. I have already been bewildered over the crash of vers 7.

 

ALSO, I noticed that when I did install the EMC 9 "Complete" during the install I was never prompted for the Content Disc. Is this normal?

 

The Content Disk is an .exe disk, so you will not get a prompt to install it. After EMC 9 is up and running, reboot, then install the Content disk.

 

Do your system specs. far exceed the minimum requirements for EMC 9?

 

What caused your problem with EMC 7? If you installed IE7, EMC 7 will no longer work properly.

[ksamdj]

The Content Disk is an .exe disk, so you will not get a prompt to install it. After EMC 9 is up and running, reboot, then install the Content disk.

 

Do your system specs. far exceed the minimum requirements for EMC 9?

 

What caused your problem with EMC 7? If you installed IE7, EMC 7 will no longer work properly.

 

 

Yes, my sytem has far more then what is required....... I didn't realize that upgrading to IE 7 was the problem until I tried to burn a DVD. Then after reading this forum I removed IE 7 and EMC 7 still didn't work.

[grandpabruce]

Yes, my sytem has far more then what is required....... I didn't realize that upgrading to IE 7 was the problem until I tried to burn a DVD. Then after reading this forum I removed IE 7 and EMC 7 still didn't work.

 

You have to uninstall both IE 7 and EMC 7, reboot, and install EMC 7 again. I had to do that with EMC 7.5.

 

The unfortunate thing is IE 7 ruined a multitude of programs. I didn't care for IE 7, so I am back at IE 6.